如下為我司愛澤工業IZE_Industries本月到貨MAZURCZAK相關產品，歡迎致電索取樣本資料和產品信息。
MAZURCZAK溫度傳感器TF02-60BC-F
MAZURCZAK溫度傳感器TF02-30BC-F
MAZURCZAK加熱器PHK46-700100-3.5380Ds K2-BC9
MAZURCZAK加熱器ROTKAPPE B-WKB 650-10004,5-380Ds9
MAZURCZAK溫度傳感器TF系列介紹
該溫度傳感器的功能基于其內置的 Pt100 傳感元件。溫度測量原理是利用 Pt100 元件的電阻值隨溫度變化的特性：在 0°C 時，該元件的電阻精確為 100 Ω；隨著溫度升高，元件電阻的變化與溫度變化成正比。
配套的電子單元向 Pt100 元件通入微弱的恒定電流，并測量元件兩端的電壓。隨后，利用歐姆定律 (R = U/I) 即可計算出元件電阻，進而確定溫度值。
電子單元與 Pt100 元件之間的連接可采用 2 線、3 線或 4 線制。我們提供 4 線制連接方案，因為該方案能夠補償連接導線自身的電阻。
導線電阻可能會導致測量結果出現顯著偏差，尤其是在導線較長的情況下。因此，溫度傳感器與電子單元之間的連接距離不應超過 50 米，且通常應采用 3 線或 4 線制連接。若距離更長，可加裝輸出標準 4…20 mA 信號的溫度變送器。
該類溫度傳感器配有 PFA 材質的柔性保護管（直徑 6 mm），標準長度為 1.6 米（也可提供其他長度）；其耐化學腐蝕性能佳，最高工作溫度可達 200°C。它們適用于潔凈室環境（材料生理無害），并可安裝在空間受限的工廠設備及儲罐的測量點上。Pt100 傳感元件（有效測量長度為 50 mm）安裝在保護管的末端。
The function of the temperature sensor results from the integrated Pt100 sensor element. The temperature is determined from the temperature-dependent change in the electrical resistance of the Pt100 element. At 0°C, the element has a resistance of exactly 100 Ω. As the temperature increases, the resistance of the element changes in direct proportion to the temperature change.
A suitable electronic unit generates a low, constant current through the Pt100 element and measures the resulting voltage across the element. The resistance of the element, and thus its temperature, can then be determined with the aid of Ohm’s Law (R = U/I).
The connection between the electronic unit and the Pt100 element can be made with 2, 3 or 4 wires. We provide 4-wire connections because these permit compensation for the resistance of the connecting wires.
Particularly in the case of long wires, the measurement result can be significantly distorted by the wire resistance. Therefore, the connection of temperature sensors to electronics should not exceed 50 m and should be executed generally with 3 or 4 wires. For longer lengths, it is possible to interpose a temperature transmitter with a standard out put signal of 4…20 mA.
Temperature sensors with a flexible protective tube made of PFA (? 6 mm) with a standard length of 1.6 m (other lengths possible) are extremely resistant to chemicals and the maximum operating temperature is 200°C. They are also suitable for use in cleanroom applications (physiologically benign) and can be mounted to the measuring point in plants and tanks where space is limited. The Pt100 sensor element, with an active measuring length of 50 mm, is mounted to the end of the protective tube.
MAZURCZAK加熱器CALOR系列介紹
CALOR 筒式加熱器特別適用于直接加熱清洗液和堿性溶液。
該筒式加熱器采用陶瓷槽體結構，具有高電氣絕緣性能、良好的機械強度以及抗溫度波動能力。內部裝有線圈狀的高溫加熱絲，以確保良好的散熱效果并延長加熱器的使用壽命。
接線頭下方的非加熱區長度可根據需求定制，最小長度為 50 毫米；我們也可根據您的具體要求延長該非加熱區。
該加熱器支持各種額定電壓，最高可達 500 V，并可配置為單相、雙相或三相連接。
可以根據具體需求提供多種金屬材質及各種安裝方式。浸入式套管的表面功率密度也可根據應用場景進行定制。這種個性化定制設計不僅能確保系統運行穩定可靠、延長使用壽命，還能避免對被加熱液體造成損害。
CALOR cartridge heaters are especially suitable for direct heating of cleaning solutions and alkalines.
Cartridge Heater Specifications
The cartridge heaters consist of ceramic groove bodies with high electrical insulation values, good mechanical strength and excellent temperature fluctuation resis tance. A high temperature heating wire is fitted as a coil in order to ensure good heat radiation and a long life span of the cartridge.
The unheated zone below the connection head can be designed individually and is at least 50 mm. However, we can also extend this unheated zone according to your wishes.
The cartridges are available in every rated power voltage up to a maximum of 500 V. The connection can be one, two or three phase.
Immersion Tube Material Specifications
We can offer you different metallic materials with the most varied fixing methods according to your requirements or demands. The surface power density of the immersion tube can be custo mized to suit your application. This individual custom design guarantees you the faultless operation of your system, a long life span and prevents damage to the heated liquid.
MAZURCZAK加熱器ROTKAPPE系列介紹
ROTKAPPE 角形浸入式加熱器是針對液位較低或液位波動較大的各類容器進行直接加熱的理想方案。水平布置的加熱管段負責從容器底部加熱液體，從而確保了最佳的熱輻射效果和均勻的熱量分布。
額定功率取決于水平加熱管段的長度。由于整段管長均可用于加熱，因此能夠實現較高的加熱功率。垂直的非加熱管段可根據容器深度進行定制調整。
幾乎可以根據客戶的具體要求，針對各種容器尺寸進行定制設計。緊湊的結構設計節省了空間，從而有助于實現更具成本效益的規劃布局。
通過調整額定功率和加熱管長度，可以輕松適應工藝液體所允許的最大表面功率密度要求。
ROTKAPPE 角形浸入式加熱器由水平加熱管段、長壽命加熱芯、垂直非加熱管段、接線盒及電源線組成。
浸入式加熱管
水平管段與垂直管段焊接為一體。采用多種金屬材質制造的加熱管確保了優異的耐化學腐蝕性能。高品質材料的使用保證了產品的高可靠性與長使用壽命，從而確保系統正常運行。水平加熱管段上焊有角形支架，以確保加熱器與容器底部或固定點之間保持必要的最小間距。
長壽命加熱芯
長壽命加熱芯采用具有高電氣絕緣性能和良好機械強度的開槽陶瓷體制造。耐高溫加熱絲以線圈形式纏繞其中，以實現從加熱管向液體的最佳熱輻射效果。適用于角形浸入式加熱器的加熱芯提供多種額定電壓規格（最高可達 500 V），支持單相、兩相及三相連接。加熱芯不可由用戶自行更換。
ROTKAPPE angular immersion heaters are the ideal method of direct heating for all containers with a low liquid level or high level fluctuation. The heating of the liquid from the container bottom is achieved by the horizontal heated immersion tube and this ensures optimum heat radiation as well as good heat distribution.
The rated power is determined by the length of the horizontal immersion tube. A relatively high heating performance is also possible because the entire tube length can be used for heating. The vertical, unheated immersion tube section can be adapted to the container depth.
Nearly every desired adaptation to the container size can be realized according to specific customer requirements. The compact type of construction saves space and as a result you can plan more cost effectively.
An adaptation to the maximum permissible surface power density of the process liquid can be easily done by variation of the rated power and the immersion tube length.
ROTKAPPE angular immersion heaters consist of the heated horizontal immersion tube, the long-life heating cartridge, the unheated vertical immersion tube, the terminal casing and the lead.
The Immersion Heater Tube
The horizontal and the vertical immersion tubes are welded toge ther. Good chemical resistance is ensured by using the various metal immersion tube materials. A long lifespan with optimum reliability is assured by using high quality materials, thereby ensuring faultless operation of your system. Angle shaped supports are welded onto the horizontal immersion tube in order to observe the mini mum distance to the container bottom or fixing.
The Long-life Heating Cartridge
Long-life heating cartridges are made from ceramic groove bodies with high electrical insulation values and good mechanical strength. A high temperature resistance heating wire is fitted as a coil in order to achieve the best possible heat radiation from tube to liquid. The cartridges for angular immersion heaters are available in rated voltages up to a maximum of 500 volts for one, two and three phase connections. The cartridges cannot be replaced by the user.
MAZURCZAK產品常用型號：
MAZURCZAK TF02-60BC-F
MAZURCZAK A043388
MAZURCZAK A043638
MAZURCZAK B-FC 800/1,6-400 Ds
MAZURCZAK B-KB 1000/3,5-400 DS
MAZURCZAK B-KB 2000/5,0-400Ds
MAZURCZAK B-KB 800/2.5-400 DS
MAZURCZAK B-KB1000/3.5-400 Ds
MAZURCZAK B-KB1250/4.0-400 Ds
MAZURCZAK B-KB800/1.6-400DS
MAZURCZAK B-KB800/1.6-400DS/FFA
MAZURCZAK B-PS 630/1,25-230WS
MAZURCZAK B-PS-630/1.6 400DS
MAZURCZAK B-Ti 800/2,0-400 Ds
MAZURCZAK B-WKB 635-750/3,15-400DS K2/9
MAZURCZAK B-WKB 635-7503,15-400DS K29
MAZURCZAK B-WKB 650-1000/4,5-380Ds/9
MAZURCZAK B-WKB 650-1000/4.5-380DS/9ART
MAZURCZAK B-WKB 750-1150/4.5-380DS/9ART
MAZURCZAK B-WKB 800-750/3,0-400Ds
MAZURCZAK B-WKB-750-750/3,0-400Ds/BK
MAZURCZAK B-WKB635-750/3.15-400DS K2/9
MAZURCZAK BWKB 900-1250/5,0-400 DS
MAZURCZAK DSW3/1
MAZURCZAK GALMATHERM P40 17905JF19A1
MAZURCZAK IVS3/16-20-70/LC-T
MAZURCZAK L-TG 400/0
MAZURCZAK MTSu 53 (BC-L-L-3) L21
MAZURCZAK NS 3/10 13-30 BC-K
MAZURCZAK NS3/10-20-70/LC-B
MAZURCZAK NS3/10-20-70/LC-T
MAZURCZAK NS33/10-20-70/LC-K
MAZURCZAK NS4/10-13-20-70/LC-K
MAZURCZAK NS4/10-15-30-50/LC-B
MAZURCZAK NS4/10-20-30-70/LC-K
MAZURCZAK NS4/10-20-30-70/LC-В
MAZURCZAK NS4/10-30-50-60/LC-B
MAZURCZAK NT 2/20-30/30/LC-K
MAZURCZAK NT 3/10-12-30/25/BC-K
MAZURCZAK NT2/20-30/25/LC-K/L Temp
MAZURCZAK NT2/20-30/30/lc-k
MAZURCZAK NT3/15-15,5-30/25/LC-B/L
MAZURCZAK P 30 05202 KF 22 R/9
MAZURCZAK P 40 10605 KF 22 R/9
MAZURCZAK P 40 13135 KF 24R/9
MAZURCZAK P 40 15905 JF 22 M1
MAZURCZAK P3012455
MAZURCZAK P40 17905 JF 19 A1
MAZURCZAK PHK 40-1400/100-5,0/400 Ds K1-B/9
MAZURCZAK PHK 40-700/100-2,5/400 Ds K1-B/9
MAZURCZAK PHK 40-900/100-3,5/400 Ds S1-B/9
MAZURCZAK PHK 40-900/100-3,5/400 Ds-K1-B9
MAZURCZAK PHK46-1000/100-5.0/400
MAZURCZAK PHK46-700/100
MAZURCZAK PHK46-700100-3.5380Ds K2-BC9
MAZURCZAK PHK46-800/100-4.0/400DS K1-BC/9
MAZURCZAK PHK46-800/100-4.0/400DS K1-BK/9
MAZURCZAK PHP 46-1400/100/5.0-400 DSK 1-B/9
MAZURCZAK PVDFMTSu45/PG-L/9 51008441
MAZURCZAK PVDFMTSu60/PG-L/9 51008195
MAZURCZAK ROTKAPPE B-KB 1000/3,5-400 DS
MAZURCZAK ROTKAPPE B-WKB 650-10004,5-380Ds9
MAZURCZAK SK25/04179-00
MAZURCZAK TF 29-30/ BC-G
MAZURCZAK TF01-160/SOG-M
MAZURCZAK TF02-30/BC-F
MAZURCZAK TF02-30BC-F
MAZURCZAK TF02-40/LC-B
MAZURCZAK TF02-60/BC-F
MAZURCZAK TR-TF 50/LCG
MAZURCZAK TR-TF50/LC-G
如果您需要完整的MAZURCZAK的相關技術咨詢，請隨時致電愛澤工業，或者訪問網站,我們將盡全力解決您的問題。
If you have any question for MAZURCZAK，Please feel free to communicate with us and we will do our best to solve your problem.
